Ariston washing machine malfunctions

Ariston washing machines from the Italian manufacturer are distinguished by quality and reliability. But such an excellent technique sometimes fails. In some cases, malfunctions of the Ariston washing machine can be eliminated on their own, since they are of a typical nature and involve the replacement of a failed element. In this article we will look at typical problems of a multifunctional washing machine and talk about ways to solve them.

to contents ↑

Common Ariston Washing Machine Problems

Hotpoint Ariston washing machines appeared on the home appliance market many years ago, and today there are about 80 models that successfully perform their functions. Advantages of the Ariston technique are as follows:

• High quality wash.
• Operational safety.
• Reliability.
• Durability.
• Noiselessness.
• Ergonomic design.

Important! Each modern model is equipped with new additional features that facilitate the washing process and make it better. However, with high reliability and ease of management, the equipment can break down. The vast majority of breakdowns of the washing machine are associated with improper operation. These are gross errors of the user when using the equipment, and hard water, which can completely disable household appliances. In the case when the purchase of a new washing machine is inevitable, our model will help you find the right model and get acquainted with its characteristics “TOP of the best front-loading washing machines”.

If we consider the most frequent breakdowns of Ariston appliances, then, based on the data of service centers for repairing household appliances, we can make a kind of malfunction rating:

1. Blockages. It is with clogs that the masters have come across most often. Although the blockages themselves are not considered a breakdown, it is they that most often disrupt the operation of the washing machine.
2. Damage to the heating element (TENA). Despite the fact that the heater in the household appliances “Ariston” is of high quality, hard water can destroy it over time.
3. Drain pump (pump). This part rarely fails. In most cases, this occurs as a result of wear of the pump during prolonged use of the unit.
4. Gasket in the filler valve. Very rarely, the filler valve fails, or rather, not the valve itself, but a rubber gasket, which eventually becomes stiff and begins to let water through. The gasket itself is inexpensive, but the services of the master to replace it with cheap can not be called.
5. Oil seals and bearings. Continuous operation of the equipment causes the bearing shaft to wear out, as a result of which moisture can enter it. In Ariston washing machines, such a problem is a rarity. But if this happened, you can’t continue to use the device, as this can lead to more serious problems - a violation of the drum attachment and damage to the tank.
6. Electronics and electrics. These problems are extremely rare.

Important! Before proceeding with an independent repair of equipment, it is necessary to accurately determine the cause of the malfunction. Manufacturers have foreseen this moment, and so have we. Our review will help you in more detail. error codes of washing machines Ariston.

Next, we will examine each malfunction in detail and tell you how to repair the Ariston washing machine with your own hands.

to contents ↑

Ariston Washing Machine - Diagnostics

To determine the breakdown, it is necessary to establish an approximate “diagnosis” of the symptoms of the behavior of the equipment:

• If after prolonged use of the machine there is noise during the spin cycle or the washing quality noticeably decreases, the cause of this “behavior” of the unit may be a blockage or a malfunction of the pump (pump).
• If the laundry after pressing is wet, then most likely there are problems with the drain hose, or this is a consequence of a blockage and a breakdown of the pump.
• Water drains too slowly. The problem may be in the drain hose, pump, or a breakdown in the pressure switch relay.
• If the water does not heat up, then the heater burned out.
• If you hear a creak during the spin cycle or a knock that accompanies the entire washing process, it is possible that a foreign object has appeared between the drum and the rubber band or the drum mount has loosened.
• If you hear a metallic “clanging” sound, then this threatens a serious repair, since, most likely, the problem is in the shaft bearings.
• The creaking that continues during the entire washing and spinning process indicates that the shock absorbers or springs on which the tank is hung are worn out. Perhaps the creak is caused by the tension and loosening of the drive belt.

Important! In the event of any breakdown, the display of the Ariston washing machine displays a malfunction code (error). Knowing the meaning of the code will help you quickly identify and resolve the problem.

Having determined the possible cause of the breakdown, proceed with the repair.

to contents ↑

Clogging problems

If there are problems with blockages, then do not rush to call the master, since you can fix such a malfunction yourself. The main sign of blockage is the idle operation of the drain pump: there is buzz, but the water does not leave the tank. Typically, this problem occurs after washing, when the machine cannot drain the water to begin rinsing.

Most often, blockage occurs:

• In the drain filter, this is the most common blockage.
• In the drain hose.
• In the drain pipe.
• In the pump.

Drain filter

To clear the filter block, proceed as follows:

1. Open the narrow sunroof on the front of the device.
2. Place any container or rag to soak up any leaking water.
3. Unscrew the drain filter, which is located at the bottom right under the narrow panel.
4. Clean the filter and screw it back.

Hose, nozzle, pump

If the debris is stuck before reaching the drain filter, it is necessary to clean the nozzle between the tank and the filter or check the pump. In order to get rid of clogging in these elements of the machine, perform the following operations:

• Unplug the machine.
• Shut off the water supply.
• Remove the front panel of the housing.
• Lay the machine on its side so that the pump is at the top.

Important! You can access the details by removing the back wall. Act as you please.

• Place a basin and a rag to drain the water.
• Remove the screws to remove the bottom panel.
• To remove the pipe, loosen its clamp. A branch pipe is a corrugation. To understand if there is a blockage in the pipe, remember the corrugation in several places and look at it in the light. If a large object is stuck in the nozzle, you can feel it with your hands.
• If the pump is clogged, disconnect the wires and loosen the clamps holding the nozzle. Remove the two screws that secure the two halves of the pump housing together. Inspect the impeller (twist the blades); if necessary, clean it.

Important! Do not forget to check the sewer, as blockage can occur in it. A common clog in the drain pipe can lead to improper operation of the washing machine.

to contents ↑

Faulty valve or pump

Diagnosing the failure of the filler valve is quite simple.In the event that the valve, due to a malfunction, stops blocking the water, then water begins to flow by gravity into the washing machine’s tank, even if the appliance is disconnected from the mains.

Important! If the washing machine is turned off, and you hear the murmur of water being poured into the tank and drained from it, then be sure that the filling valve is out of order. The water folding valve (inlet) is an electromechanical device.

Such a malfunction of the Ariston washing machine can be caused by the following reasons:

• Burnout of the electrical part.
• Loss of membrane elasticity.
• Clogging.

Valve

In the event of a valve breakdown, proceed as follows:

1. Unplug the appliance.
2. Close the water inlet and completely drain the remaining fluid from the machine.
3. Remove the top or back of the chassis.
4. If the valve is clogged, unscrew the water inlet hose, remove the filter and clean.
5. To check the valve for leaks, unscrew it from the body, connect the water inlet hose to it and open its supply tap.
6. Check the performance of the coils by supplying them with alternating voltage of 220 V. A working device will alternately pass water from the tube to the section of which the voltage is supplied.
7. To check the resistance on the coils, install the ohmmeter probes on the valve contacts. Normally, the device should show 30-50 ohms.

Important! In the filling valve, it is impossible to repair any malfunction, except for a blockage. The defective valve should be replaced with a similar one. It is also not possible to replace this part on your own, so you should contact a service center for help.

water pump

Another common problem may be a pump breakdown. If at the moment when water should be drained from the car, only a characteristic hum is heard, and in some cases - complete silence, then we can conclude that the pump is broken. In the Ariston washing machine, the pump is located at the bottom of the appliance, so you can get to it only through the bottom. DIY repair of the Ariston washing machine is not possible in this case - it is better to entrust the replacement of the drain pump to a specialist.

If the pump casing is deformed by hot water, and the blades touch it and cannot spin, then the situation can be corrected as follows:

1. Disconnect the pump from all wires and hoses.
2. Unscrew the pump casing.
3. Remove the screws that secure the pump scroll to its body.
4. Mark with a marker the position of the engine in relation to the cochlea.
5. Pull the engine out of the cochlea.
6. Use a sharp knife to cut each impeller blade. Cut a small amount of material so that the stroke of the blade is free, but do not overdo it, otherwise, you can negate the performance of the pump.
7. Reassemble all parts in reverse order and make a trial run.

to contents ↑

The heating element is out of order

The heater is the most important part of the washing machine, responsible for heating the water in the tank and the quality of the wash. If the heating element is faulty, the wash either does not start at all and the system gives an error (FO3), or the wash is done in cold water.

Checking the heater in the device is not difficult:

1. Remove the back cover of the unit.
2. Locate the service hatch located at the bottom of the rear wall.
3. Unscrew the screws and squeeze the clamps with a screwdriver. Remove the service hatch cover.
4. Find behind the lid under the tank two large contacts with the fastener in the middle - this is the heater.
5. Loosen the screw and carefully pull out the heater.
6. Ring the heating element with a multimeter. Two wires TENA close between themselves. The multimeter should make a sound and light the indicator. Touch one end of the appliance to the heater housing and the other to its terminals. If the device protects, this means that the heater breaks into the case and the element must be replaced.

 

to contents ↑

Bearings are out of order

The weak point of the Ariston washing machines is a non-separable tank.Therefore, a simple, seemingly, replacement of bearings on their own is quite difficult. It is possible to recognize the breakdown of the bearing and stuffing box by unpleasant sounds. The shaft begins to rub against the sleeve and gradually destroys it. If no action is taken, the drum will begin to lift and damage the tank.

If the first signs of parts failure appear, consult a specialist or try replacing the bearing yourself. This work is complicated. The main difficulty is that the unit must be completely disassembled and the tank separated from the body. In addition, you must correctly remove the old bearings, and then carefully install the new ones. Without proper dexterity, this repair cannot be done on its own. But, if you are determined to do the work with your own hands, then carefully study the unit's device and follow the step-by-step instructions.

To replace the bearings, you will need the following tools and materials:

• Hammer.
• Pliers.
• Screwdrivers and wrenches.
• Sealant.
• Special aerosol.
• New bearings.

Step-by-step instructions for replacing a bearing:

• Switch off the appliance and turn off the water supply.
• Take a picture of the wiring of the device before disassembling it.
• Disassemble the washing machine completely. Since the drum is between the two bearings, it must also be removed.

Important! If the edge of the tank is rolled on the sealant, then heat the edge with a gas burner and expand it. If the tank is plastic, then cut it exactly along the seam with a hacksaw for metal. Heat the bolts filled with glue and unscrew the fasteners.

• Pull one drum part after another. The rotating part of the drum should remain with the rear wall on the bearings.
• Carefully pull out the shaft with the bearings. To unscrew the pulley bolt, grind one or two of its edges with a grinder. So it is easier to hold it with a key.
• The bearings cannot be pulled off just like that, so the inner cage of the parts must be carefully chopped with a grinder and removed from the shaft. This must be done carefully so as not to damage the oil seal.
• Measure the shaft diameter with a vernier caliper, select similar bearings.
• Thoroughly clean the seat of the parts, grease it.
• Insert a new bearing - if necessary, put grease in it.

Important! It is better to buy bearings sealed, assembled with rubber glands.

• Gently tap the outer edge of the bearing to hammer it all the way (a distinctive dull sound should appear).
• Put the shaft back in place, put the sealant (for example, aquarium). Roll the edge back.
• Bolts put on special glue. It is sold in car dealerships and is designed to fix threaded connections.
• Collect the sawn plastic tank on the screws, applying sealant between the halves.

Important! The above method of replacing bearings cannot be called simple, therefore, if you do not have experience, skills and appropriate tools, then it is better to provide such repairs to specialists from the service center.

to contents ↑

Stock footage

Manufacturers of household appliances “Ariston” took care not only of multifunctionality and quality, but also of a self-diagnosis system. Carefully read the error codes displayed on the electronic display to know what kind of malfunction of the “Ariston” washing machine with a vertical or horizontal load this indicates. Knowing about errors and breakdowns, you can easily eliminate the cause of the malfunction yourself or turn to specialists for help. However, in order to extend the life of the unit and not subject the “household assistant” to repair, strictly follow the operating rules prescribed by the manufacturer, regularly carry out all maintenance procedures for the components and parts of the machine!